CMIT 5 U
$4,220.00 + gst
To enquire about this product - click here
The CMIT 5 has set a new standard for shotgun microphones since its release. The CMIT 5's directionality increases smoothly with higher frequencies, which results in a very balanced sonic character. In addition to this, the microphone's sound level decreases softly yet steadily for off-axis sounds, allowing these to be recorded neutrally as well as reducing the effects of movement during boom operation. The CMIT 5 also has a much stronger directionality than one might expect from a microphone of its length. If required, the CMIT 5 can also be used for music recordings, for example opera recordings.
Three pushbutton-activated filters allow the microphone to adapt to the recording situation:
High-frequency emphasis (+5 dB at 10 kHz) enhances speech intelligibility, and compensates for high-frequency loss caused by windscreens;
A steep low-cut filter (18 dB/oct. below 80 Hz) suppresses wind and boom noise;
A gentle low-frequency rolloff (6 dB/oct. below 300 Hz) compensates for proximity effect.
Pairs of LEDs next to each pushbutton indicate the status of the filters. Even in darkness the user can read the settings and see that the microphone is operational. The settings are retained when the microphone is switched off.
The capsule and amplifier of the CMIT 5 are built as a single unit, unlike microphones of the Schoeps Colette series.
Tech Specs:
Pickup pattern : Supercardioid / lobe-shaped
Frequency range : 40 Hz - 22 kHz
Sensitivity : -35 dB (V/Pa), 17 mV/Pa
Equivalent noise level (A-weighted) : 14 dB
Equivalent noise level (CCIR) : 24 dB
Signal-to-noise ratio (A-weighted) : 80 dB
Maximum sound pressure level (THD < 0.5 %) : 132 dB-SPL (P48)
Maximum output voltage : 1.3 V (2.5 dBV) with 1 kΩ load
High shelf filter : switchable, +5 dB at 10 kHz
Low cut filter : switchable, 80 Hz, 18 dB/oct.
Proximity filter : switchable, 300 Hz, 6 dB/oct.
Minimum recommended load impedance : 1 kΩ
Output impedance : 50 Ω
Maximum cable length : > 400 m
Schoeps RFI Shield : Yes
Powering standard / Valid range : P48 / >34 V
Current consumption : 4.4 mA (P48)
Common mode rejection ratio (at 1 kHz) : > 65 dB
Output : XLR-3M, analog, 1 channel
Length : 251 mm
Diameter : 21 mm
Weight : 95 g
Surface finish : Blue
Custom colour : Anthracite Grey, Chromagreen (Additional Fee + Longer Lead Time)
$4,220.00 + gst
To enquire about this product - click here
The CMIT 5 has set a new standard for shotgun microphones since its release. The CMIT 5's directionality increases smoothly with higher frequencies, which results in a very balanced sonic character. In addition to this, the microphone's sound level decreases softly yet steadily for off-axis sounds, allowing these to be recorded neutrally as well as reducing the effects of movement during boom operation. The CMIT 5 also has a much stronger directionality than one might expect from a microphone of its length. If required, the CMIT 5 can also be used for music recordings, for example opera recordings.
Three pushbutton-activated filters allow the microphone to adapt to the recording situation:
High-frequency emphasis (+5 dB at 10 kHz) enhances speech intelligibility, and compensates for high-frequency loss caused by windscreens;
A steep low-cut filter (18 dB/oct. below 80 Hz) suppresses wind and boom noise;
A gentle low-frequency rolloff (6 dB/oct. below 300 Hz) compensates for proximity effect.
Pairs of LEDs next to each pushbutton indicate the status of the filters. Even in darkness the user can read the settings and see that the microphone is operational. The settings are retained when the microphone is switched off.
The capsule and amplifier of the CMIT 5 are built as a single unit, unlike microphones of the Schoeps Colette series.
Tech Specs:
Pickup pattern : Supercardioid / lobe-shaped
Frequency range : 40 Hz - 22 kHz
Sensitivity : -35 dB (V/Pa), 17 mV/Pa
Equivalent noise level (A-weighted) : 14 dB
Equivalent noise level (CCIR) : 24 dB
Signal-to-noise ratio (A-weighted) : 80 dB
Maximum sound pressure level (THD < 0.5 %) : 132 dB-SPL (P48)
Maximum output voltage : 1.3 V (2.5 dBV) with 1 kΩ load
High shelf filter : switchable, +5 dB at 10 kHz
Low cut filter : switchable, 80 Hz, 18 dB/oct.
Proximity filter : switchable, 300 Hz, 6 dB/oct.
Minimum recommended load impedance : 1 kΩ
Output impedance : 50 Ω
Maximum cable length : > 400 m
Schoeps RFI Shield : Yes
Powering standard / Valid range : P48 / >34 V
Current consumption : 4.4 mA (P48)
Common mode rejection ratio (at 1 kHz) : > 65 dB
Output : XLR-3M, analog, 1 channel
Length : 251 mm
Diameter : 21 mm
Weight : 95 g
Surface finish : Blue
Custom colour : Anthracite Grey, Chromagreen (Additional Fee + Longer Lead Time)
$4,220.00 + gst
To enquire about this product - click here
The CMIT 5 has set a new standard for shotgun microphones since its release. The CMIT 5's directionality increases smoothly with higher frequencies, which results in a very balanced sonic character. In addition to this, the microphone's sound level decreases softly yet steadily for off-axis sounds, allowing these to be recorded neutrally as well as reducing the effects of movement during boom operation. The CMIT 5 also has a much stronger directionality than one might expect from a microphone of its length. If required, the CMIT 5 can also be used for music recordings, for example opera recordings.
Three pushbutton-activated filters allow the microphone to adapt to the recording situation:
High-frequency emphasis (+5 dB at 10 kHz) enhances speech intelligibility, and compensates for high-frequency loss caused by windscreens;
A steep low-cut filter (18 dB/oct. below 80 Hz) suppresses wind and boom noise;
A gentle low-frequency rolloff (6 dB/oct. below 300 Hz) compensates for proximity effect.
Pairs of LEDs next to each pushbutton indicate the status of the filters. Even in darkness the user can read the settings and see that the microphone is operational. The settings are retained when the microphone is switched off.
The capsule and amplifier of the CMIT 5 are built as a single unit, unlike microphones of the Schoeps Colette series.
Tech Specs:
Pickup pattern : Supercardioid / lobe-shaped
Frequency range : 40 Hz - 22 kHz
Sensitivity : -35 dB (V/Pa), 17 mV/Pa
Equivalent noise level (A-weighted) : 14 dB
Equivalent noise level (CCIR) : 24 dB
Signal-to-noise ratio (A-weighted) : 80 dB
Maximum sound pressure level (THD < 0.5 %) : 132 dB-SPL (P48)
Maximum output voltage : 1.3 V (2.5 dBV) with 1 kΩ load
High shelf filter : switchable, +5 dB at 10 kHz
Low cut filter : switchable, 80 Hz, 18 dB/oct.
Proximity filter : switchable, 300 Hz, 6 dB/oct.
Minimum recommended load impedance : 1 kΩ
Output impedance : 50 Ω
Maximum cable length : > 400 m
Schoeps RFI Shield : Yes
Powering standard / Valid range : P48 / >34 V
Current consumption : 4.4 mA (P48)
Common mode rejection ratio (at 1 kHz) : > 65 dB
Output : XLR-3M, analog, 1 channel
Length : 251 mm
Diameter : 21 mm
Weight : 95 g
Surface finish : Blue
Custom colour : Anthracite Grey, Chromagreen (Additional Fee + Longer Lead Time)